Go Deal Now

 

 

They are making a number of good points on A Step-by-Step Guide to Installing a Bathtub as a whole in this content which follows.

Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall surface to remove the old bathtub as well as place the new bath tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and also set in the brand-new one. Make certain you have certified yourself for the task and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly assist you install a new bath tub in your restroom if you have actually already purchased a brand-new tub and also don't require to change the plan of your previous water supply pipes.
Your devices and material checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Planning for the Installation

First of all, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop stress on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last position.

 

 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Bathtub

Making use of both wooden boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if required. Fill the bath tub and additionally inspect the overflow outlet and also the typical electrical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has actually been used a minimum of once as this will certainly settle it right into its final placement.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in area between the tap and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with moisture and also feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the activity experienced when the tub remains in use. The sealer can crack fairly very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about Tools You Need to Install a New Bathtub ? Put feedback below. We would be delighted to hear your reactions about this entry. In hopes that you come back again in the near future. Don't hesitate to take a moment to share this page if you appreciated it. Thanks so much for your time spent reading it.

Start Now